Canon MG3600 Printer Troubleshooting: Common Problems & Fixes

Canon MG3600 Printer Troubleshooting

Canon MG3600 printer troubleshooting usually comes down to one question: how many times is the Alarm lamp flashing? Canon’s own manual ties each flash count to a specific cause, so a printer that looks stubborn is often telling you exactly what’s wrong. This guide covers the jams, ink warnings, offline errors and Wi-Fi snags that owners run into, plus the few faults no amount of button pressing will fix.

One note on scope. The MG3600 series is a family, and Canon’s support code list covers the MG3610, MG3620, MG3640, MG3650, MG3660, MG3670 and MG3680. Where button steps matter, check them against the manual for your exact model.

Canon MG3600 printer troubleshooting starts with the alarm lamp

Canon’s manual separates two lamp patterns. The Alarm lamp flashing on its own points to something you can often fix at your desk. The ON and Alarm lamps flashing in turn point to a printer error, and a few of those end at a repair counter.

For the first pattern, Canon’s lamp reference gives these causes:

Alarm lamp flashes What Canon says it means Support code
2 Out of paper, paper not feeding, or a paper size mismatch 1003, 2100, 2101
3 Output tray closed, or paper jammed 1250, 1300, 1303, 1304
4 FINE cartridge not seated properly 1687
5 FINE cartridge missing or not recognized 1401, 1403, 1485
6 Output cover open, or cartridge in the wrong position 1202, 1486, 1487
8 Ink absorber almost full 1702 to 1705, 1712 to 1715
9 Protective tape or material still on the cartridge holder 1890
13 Ink may have run out 1686
16 Ink has run out 1688

Count a few full cycles before you trust your number, then open the page for the matching support code, because that page holds the actual steps and the table above only tells you which page to open.

A March 2024 thread on Canon’s community forum shows why this matters. An owner wrote that the printer handled one job, then the Alarm lamp started flashing and nothing else would print. The reply named no cause and sent the owner to Canon’s error code article. That’s fair. The lamp is the diagnosis, and without the count nobody can read it.

Paper jams and paper that won’t feed

Two flashes means the printer thinks it has no paper or can’t pull it in. For support code 1003, Canon says to reload the paper and press the Black or Color button. Push the stack in until its leading edge reaches the back end of the front tray, because a stack that sits short of the back is the first thing worth ruling out.

Three flashes usually means a jam. Code 1300 covers paper stuck at the output slot, and Canon’s advice is specific:

  1. Pull the paper out slowly with both hands so it doesn’t tear.
  2. Don’t pull paper out of the front tray, since that can damage the machine.
  3. If it won’t come free, turn the printer back on and it may eject the sheet itself.
  4. If you have to switch it off mid print, press Stop first.
  5. Reload suitable paper, press Black or Color to resume, and reprint any page that came out wrong.

Canon also warns against A5 paper for photos or graphics. It can curl and jam on the way out. If you print photos on small sheets and keep clearing jams, that’s the first habit to change.

Then there’s the odd case. In an older community thread, an MG3620 owner reported a “needs paper” message with paper loaded, plus a blank page that fed through. One reader said pressing the copy button repeatedly got their printer going again, sometimes about ten presses. Treat that as a symptom, not a fix. If correctly loaded paper still gets rejected week after week, it’s a service question.

Ink errors, and the one warning you can’t fix yourself

Four flashes means a cartridge isn’t seated. Five means one is missing or unrecognized. Reseat the FINE cartridges, make sure the cover is shut, and try again before you assume the cartridge itself is bad.

Sixteen flashes is support code 1688, which means an ink cartridge is empty. Canon gives you a way to keep working: hold Stop for at least five seconds to switch off the ink level check. Printing continues until the leftover ink runs out, though quality may suffer.

Scanning and faxing keep working as long as the empty cartridges stay installed, which is handy when you only need to scan a form at 5 p.m. and the replacement ink is still in the mail. Canon recommends new, genuine Canon cartridges when you do replace them.

Eight flashes is different. That’s the ink absorber, the part that soaks up waste ink from cleaning cycles, and Canon says it’s almost full under code 1702. Pressing Black or Color lets you keep printing for now. The lasting fix is a repair at a Canon service center. Nothing you do with cartridges or settings clears it.

My view: when this warning shows up on a printer that’s several years old, get the repair quote before you decide anything. Then you’re comparing real numbers, not guessing.

When the ON and Alarm lamps flash in turn

This pattern means the printer itself has a fault. Two flashes maps to support code 5100, and ten maps to B202 to B205, which Canon lists as errors requiring repair.

For 5100, Canon suggests this routine: cancel the print job and switch the printer off. Look for anything blocking the cartridge holder, such as a stray sheet or debris.

Then open the paper output cover, push the cartridge lock lever up to confirm the cartridges sit properly, close the cover and power back on. Don’t touch the clear film while you’re in there. If the lamps still alternate, Canon points you to service.

Code 5200 is simpler. Turn the printer off, unplug it, plug it back in and switch it on. If the error returns, that’s a repair too.

Why Windows says the printer is offline

An offline message doesn’t always mean the printer is off. A Microsoft Q&A thread on printers showing offline lists fixes that people reported:

  1. Remove the printer under Settings, Bluetooth & devices, Printers, then add it again.
  2. Open Printer Properties and make sure “Use printer offline” is unchecked.
  3. Reinstall the newest driver from the manufacturer.
  4. Restart the printer and the PC.

Sometimes none of that works. A December 2018 thread describes an MG3600 on USB that printed fine after a move from Windows 7 to 10, then began throwing “An error occurred while printing.” The Windows troubleshooter found nothing, and the latest drivers didn’t help. In the same thread, another user said printing worked from Edge but not Chrome or Internet Explorer, and nobody explained why.

Both posts are years old, so the Windows details have shifted. The useful part is the pattern. If a fresh driver doesn’t fix it, print a test page from a second app, then try a different USB cable or a different connection type, and only after that go back to reinstalling drivers for the third time.

Connecting over Wi-Fi with WPS

If your router has a WPS button, Canon’s WPS steps for this series are short:

  1. Keep the router’s WPS button within reach.
  2. Hold the printer’s Wi-Fi button until the ON lamp blinks.
  3. Tap the Black button, then the Wi-Fi button. The Wi-Fi lamp should blink fast while the ON lamp stays lit.
  4. Press and hold the router’s WPS button. You have 2 minutes from step 3.
  5. When both the Wi-Fi and ON lamps burn steadily, you’re connected.

If the Alarm lamp comes on instead, the connection fails. Run the sequence again and keep the printer close to the router.

Faded or streaky prints

Start with a standard print head cleaning. Canon’s manual for a related inkjet line says to save deep cleaning for when that doesn’t help, since deep cleaning uses more ink.

If quality still hasn’t improved, switch the printer off and try a deep clean again after 24 hours. Replace the FINE cartridge after that, and book a repair only if the problem survives a new cartridge. Button steps for cleaning differ between lines, so follow the manual for your own model.

Next time your MG3600 acts up, count the Alarm lamp flashes before you touch anything, then open the matching code in Canon’s list. Good Canon MG3600 printer troubleshooting is mostly that discipline: read the signal first, then fix only what it names.

If the signal points to the Windows or network side and you’d rather hand that off, Geeks Worldwide Solutions handles printer setup and driver installation. It’s an independent IT support company, not affiliated with Canon.

Leave a Reply

Your email address will not be published. Required fields are marked *